180TSMC_LVDS_09-ip-21771

¥10,000.00
有货
SKU
ip-21771
Brand :
更多信息
供应商 NTLab
型号 1.2 Gbps LVDS transmitter/receiver
类型 Hard IP
到期日 Silicon proven
源网址 View more
特征 TSMC CMOS 180 nm 3.3 V power supply 1.2 Gbps (DDR MODE) switching rates (600 MHz) Half-duplex or full-duplex operation mode Conforms to TIA/EIA-644 LVDS standards without hysteresis Temperature range: -60 to + 100 degree Optimized for pad-limited layout design Portable to other technologies (upon request)
详情页 View more
附件名称 180TSMC_LVDS_09_Brief.pdf
附件链接 View more
Login to view more
The interface to the core logic in receiver mode includes the signal pins (out_p and out_n) to receive data and the control pins (en_rx, ten, t_cal<1:0, oen) to configure the state of the receiver. The interface to the core logic in transmitter mode includes the signal pins (in_p and in_n) to transmit data and the control pins (en_tx, x2i) to configure the state of the transmitter. There are other two internal pins (vref12 and iref_20u_tx, iref_20u_rx) to get voltage reference and current references. IOP and ION are complementary pins to connect to the bonding pads. LVDS transceiver cell may be used for half-duplex data transmission. In this case, input oen controls the direction of the transmission (en_tx=1, en_rx=1). When oen = 1, block operates in the receiver mode .02;?’?¢.02;¢¢??????.02;¢¢€??…€?the transmitter output is in high impedance state. When oen = 0, block operates in the transmitter mode. In this case, the transmitter drives its output current into the differential LVDS line, with the polarity corresponding to the bit value being transmitted. This LVDS driver provides a double current mode (x2i=1) for system designs that employ double termination (near-end and far-end) of the differential signaling lines. Control pins (en_tx and en_rx) enable or disable transmitter and receiver. When en_tx=0, en_rx=1, block operates in the receiver mode .02;?’?¢.02;¢¢??????.02;¢¢€??…€?the transmitter output is in high impedance state and transmitter is disable. When en_tx=1, en_rx=0, block operates in the transmitter mode, receiver is disable. Block also comprises internal termination resistor with adjustable value. Input bits t_cal<1:0> are used for adjusting the termination resistance. The design target is to compensate 100 Ohm resistance deviation from 20% to 10%. In order to use an external termination, the internal resistor may be switched off by setting low input ten. The block is designed on TSMC 180 nm CMOS technology.

No video is found.
                                   

FAQ - Frequently Asked Questions

                                   

Welcome to Sparsh\'s FAQ! Here you\'ll find answers to our most asked questions. Still have something we should know? Send us an email, we\'re happy to help!

                                   

Q1: How can I change my shipping address?

                                   

A1: Consectetur morbi, suscipit donec semper vitae sed a class vivamus. Sodales montes porttitor adipiscing nisl sit dui sem fringilla elit. Sagittis lacinia montes nisl mollis lobortis cras nisi. Conubia montes odio taciti magnis morbi mauris lorem pulvinar mollis aliquam. Faucibus facilisi tempus tincidunt eu laoreet. Porta donec vitae suscipit habitasse fermentum vivamus!    

       
  • Eget est ad potenti primis id rhoncus vestibulum vestibulum. Ante est vel mattis mattis. Vel eleifend auctor lorem, odio proin quisque potenti parturient euismod. Tristique massa quis morbi netus magna pretium laoreet. Inceptos eget massa ac lacinia vitae suspendisse orci nascetur vel torquent. Feugiat eleifend eget aenean facilisi sapien proin leo dictumst semper orci ipsum? Ultrices duis tellus consequat nostra.
  •    

                                   

Q2: How do I activate my account?

                                   

A2: The instructions to activate your account will be sent to your email once you have submitted the registration form. If you did not receive this email, your email service provider’s mailing software may be blocking it. You can try checking your junk / spam folder or contact us at magento@sparsh-technologies.com

                                   

Q3: How do I cancel my orders before I make a payment?

                                   

A3: After logging into your account, go to your Shopping Cart. Here, you will be able to make a payment or cancel your order. We will not give refunds if payment is verified.

                                   

Q4: How long will it take for my order to arrive after I make payment?

                                   

A4: Members who ship their orders within Inida should expect to receive their orders within 2 working days upon payment verification depending on the count of orders received.

   

If you experience delays in receiving your order, contact us immediately and we will help to confirm the status of your order.

                                   

Q5: What are the payment methods available?

                                   

A5: At the moment, we only accept Credit/Debit cards and Paypal payments.

                                   

Q6: How do I make payments using Paypal? How does it work?

                                   

A6: Paypal is the easiest way to make payments online. While checking out your order, you will be redirected to the Paypal website. Be sure to fill in correct details for fast & hassle-free payment processing. After a successful Paypal payment, a payment advice will be automatically generated to Samplestore.com system for your order.

   

It\'s fast, easy & secure.

                                   
No posts is found.
Copyright © 2013-present Magento, Inc. All rights reserved.